ELC instructions - electromagnetic lock controllers. ELC series electromagnetic lock controllers Wooden elc lock
Instructions for ELC series electromagnetic lock controllers
ELC series controllers are designed for installation in electromagnetic locks Metakom ML-450, Accord ML-194 or similar in design.
- Can be used in conjunction with access control devices that do not have an electronic key reader.
- They are characterized by high reliability, ease of installation and operation.
- Works with Metakom TM2002, TM2003 and Dallas DS1990A electronic keys.
- Memory capacity – 508 keys (on request – 2044 keys).
- Programmable lock opening time 0.5…125 seconds in 0.5 second increments.
- Possibility of using a master key to quickly enter programming mode.
- Modifications for electromagnetic and electromechanical locks.
- Light (LED) and sound alarm for opening the lock.
- Opening button from the room.
- Built-in watchdog timer and supply voltage monitor.
- Supply voltage: 12 V AC or DC.
- Overall dimensions (without LED) 36 x 54 x 17 mm.
- Operating ambient temperature range: 30…+55°C
ELC series controllers can be supplied as part of ML-450 electromagnetic locks.
BRIEF OPERATING INSTRUCTIONS
ELC SERIES CONTROLLERS
1. PROGRAMMING THE “MASTER KEY” c) Turn on the power;
d) Wait for 4 beeps, remove the jumper;
e) Place the key on the contact device - you will hear 3 beeps;
The “master key” is programmed and the device switches to the subscriber key programming mode.
2. PROGRAMMING SUBSCRIBER KEYS
a) Apply the “Master Key” to the contact device - you will hear 3 beeps;
b) Applying the keys to the contact device one by one, enter them into the memory of the ELC series controller. Each key entry is accompanied by one sound signal. If the key is faulty or is already in memory, the signal will not follow.
c) Exit from the subscriber key programming mode is carried out by pressing the button. In this case, the device counts the duration of holding the button pressed in increments of 0.5 seconds. The calculated duration of memorization is used in the future as the duration of opening the lock.
3. PROGRAMMING THE LOCK OPENING DURATION
a) Apply the “Master Key” to the contact device - you will hear 3 beeps;
b) Press the exit button. In this case, the device will calculate the duration of holding the button pressed with an accuracy of 0.5 seconds. The calculated duration is remembered and used later as the duration of opening the lock.
4. CLEARING KEY MEMORY
a) Turn off the power to the device;
b) Close the jumper on the printed circuit board;
c) Turn on the power;
d) Wait for 4 beeps; Then there will be a ten-second pause and the sound signal will turn on again;
e) Within 3 seconds after the sound signal starts, remove the jumper;
f) After waiting for the sound signal to stop, install the jumper again;
g) After a pause (at this time the memory is being cleared), the program will restart. In this case, since the jumper remains installed, the device will enter the “Master Key” programming mode, and you will hear 4 signals (see step 1). You can program the “Master Key” or power cycle the ELC Series controller if the “Master Key” remains the same.
Note:
The “master key” is retained when the memory is cleared;
If after clearing the memory (step 4, g) you hear a long (3 seconds) beep, this indicates a malfunction of the memory chip. Repeat cleaning. If the result is negative, replace the 24C16 chip;
If within 3 seconds after the start of the sound signal the jumper is not removed (section 4, e), the ELC series controller will go into test mode - cyclically turning on / off the electromagnetic lock with a period of 6 seconds (3 seconds the lock is on, 3 seconds - switched off);
If, after the sound signal stops (section 4, f), the jumper is not installed again, the device will go into normal operation without clearing the memory.
· Characterized by high reliability, ease of installation and operation.
· Work with electronic keys MetacomTM2002, TM2003 And Dallas D.S.1990 A.
· 
Memory capacity – 508
keys (to order - 2044
key).
· Programmable lock opening time 0,5 …125 seconds in increments 0,5 seconds.
· Possibility of using a master key to quickly enter programming mode.
· Modifications for electromagnetic and electromechanical locks.
· 
Light (LED) and sound alarm for opening the lock.
· Opening button from the room.
· Built-in watchdog timer and supply voltage monitor.
· Supply voltage: 12B AC or DC.
· Dimensions (without LED) 36 x 54 x 17 mm.
Operating ambient temperature range: 30…+55°C
Controllers can be supplied as part of electromagnetic locks ML-450.
1. PROGRAMMING “MASTER KEY”
a) Turn off the power to the device;
b)
c) Turn on the power;
d) Wait for 4 beeps, remove the jumper;
e) Apply the key to the contact device - you will hear 3 signals;
“ The master key is programmed and the device switches to the subscriber key programming mode.
2. PROGRAMMING SUBSCRIBER KEYS
a) Attach “Master Key” to the contact device - you will hear 3 beeps;
b) Applying the keys to the contact device one by one, enter them into the controller’s memory. Each key entry is accompanied by one sound signal. If the key is faulty or is already in memory - a signal will not follow.
c) Exit from the subscriber key programming mode is carried out by pressing the button. In this case, the device counts the duration of holding the button pressed in increments 0,5 seconds. The calculated duration of memorization is used further as .
3. PROGRAMMING THE LOCK OPENING DURATION
a) Attach “Master Key” to the contact device - you will hear 3 signals;
b) Press the exit button. In this case, the device will calculate the duration of holding the button pressed with accuracy 0,5 seconds. The calculated duration is remembered and used later as duration of opening the lock.
4. CLEARING KEY MEMORY
a) Turn off the power to the device;
b) Close the jumper on the printed circuit board;
c) Turn on the power;
d) Wait for 4 beeps; Then there will be a ten-second pause and the sound signal will turn on again;
e) Within 3 seconds after the sound signal starts, remove the jumper;
f) After waiting for the sound signal to stop, install the jumper again;
g) After a pause (at this time the memory is being cleared), the program will restart. In this case, since the jumper remains installed, the device will enter programming mode “Master Key”, and you will hear 4 signals (see step 1). You can program “Mother Key” or turn the device power off and on again if “Master Key” remains the same.
Note:
· “Master Key” memory is saved when cleared;
· If after clearing the memory (step 4, g) you hear a long (3 seconds) beep, this indicates a malfunction of the memory chip. Repeat cleaning. If the result is negative, replace the 24C16 chip;
· If within 3 seconds after the start of the sound signal the jumper is not removed (section 4, e), the device will go into test mode - cyclically turning on / off the electromagnetic lock with a period of 6 seconds (3 seconds the lock is on, 3 seconds - off );
· If after the sound signal stops (section 4, f) the jumper is not installed again, the device will go into normal operation without clearing the memory.
More complete information about METAKOM products can be obtained from the sales department
at the address st. Usacheva, 29, bldg. 8, under. 42 (code-444) and telephones (0,
www. ***** E-mail: *****@***ru
information about delivery
Delivery times and times
Delivery of orders in Moscow is carried out at 2 working day
Delivery of the order in St. Petersburg is carried out at 3 working day, after the order is processed by the online store manager (order confirmation by phone).
- Delivery in Moscow within the Moscow Ring Road and in St. Petersburg carried out Monday through Saturday, except holidays, from 09:00 to 21:00.
- Delivery outside the Moscow Ring Road carried out Monday through Saturday except holidays,
— Delivery to suburb of St. Petersburg carried out Monday through Saturday except holidays, from 09.00 to 19.00 (without defining a minimum interval).
Delivery cost of ordered goods
— Delivery in Moscow (within the Moscow Ring Road) subject to cost order more than 2000 rubles carried out for free.
—Delivery cost in Moscow (within the Moscow Ring Road) of the order for an amount less than 2000 rubles amounts to 200 rubles.
— The cost of delivery in Moscow to areas outside the Moscow Ring Road (Zhulebino, Yu. Butovo, Mitino, etc.), as well as in the Moscow region within 10 km from the Moscow Ring Road, is 250 rubles regardless of the order amount.
— The cost of delivery within the Moscow region from 10 km to 30 km outside the Moscow Ring Road is 450 rubles regardless of the order amount.
— The cost of delivery in St. Petersburg depends on the weight of the order. The minimum delivery cost is 300 rubles
— The cost of delivery in the suburbs of St. Petersburg depends on the weight of the order. The minimum delivery cost is 450 rubles. The approximate delivery cost is calculated automatically when placing an order and is specified by the online store manager when confirming the order.
— To the cost of delivery of orders, including those delivered free of charge, weight more than 10 kg is added 20 rubles for each additional kilogram. Please check with the online store manager for the final delivery cost.
— Please note to buyers from Moscow, Moscow region, St. Petersburg and Leningrad region that order weighing 30 kg or more is delivered only to the entrance (without lifting to the floor).
Reserve goods in the store
- order with the condition of reserving goods in a retail store - 1 calendar day from the moment you receive an email notification that the order is ready for pickup
